Waterproofing Products

SB

It is a highly resistant insulating coating with strong adhesion, excellent water resistance and UV resistance, consisting of a special mineral filler and polymer components. ISONEM SB does not wear due to its structure, unlike other insulation materials. Therefore, it is very suitable for use on concrete roofs, terraces, walkways, asphalt pavements, tennis courts, and sports areas. The product is not affected by UV, snow, rain, water. If required, all kinds of ceramic, marble and similar coating can be applied on it. Economical and long lasting. No harm to human health.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 1,40 ± 0,10

pH (25°C): 7.0 – 9.0

Viscosity (25°C, mPa.s): 13000 - 14000

Solid content (% Weight): 74 ± 2

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Crack bridging flexible systems without trafficking ≥ 0.8, with trafficking 1.5 N/mm²

Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II

Solvent: Water

Concrete terrace and roof insulation,
Wet area insulation,
Concrete roads, parks, and gardens,
Hidden gutters, gutter-tile, and soffit.

Surface preparation: Firstly the application surface is cleaned from dust, dirt and oil. If there are places that require repairing, it is repaired with ISONEM M 03 Elastıc Repair Mortar or ISONEM MS Mortar Repair Mortar. Before application, absorbent substrates should be primed with the ISONEM UNIVERSAL PRIMER (1: 7 diluted with water; 1 part primer, 7 parts water). The main application should be started after the primer application is waited to dry between 4-6 hours.

Application method: ISONEM SB is a super component ready to use. The product is mixed homogeneously with the help of a mixer in the bucket for 5 minutes. After the mixture is made ready, ISONEM SB is applied to the surface in two coats and perpendicular layers to each other. It should be waited minimum of 4 hours between the coats. The product is produced in two types as "summer" and "winter" in accordance with the climate conditions and air temperature to be applied. The summer product is suitable for applications between 18 - 40 ° C and the winter product at 5 - 17 ° C.

PACKING: 5 kg, 10 kg and 18 kg in PP buckets
CONSUMPTION: 1 kg/m² (2 layers application)
5 kg: min. 5 m²/bucket (two layers application)
10 kg: min. 10 m²/bucket (two layers application)
18 kg: min. 18 m²/bucket (two layers application)
COLOR: All requested can be produced in colors.
SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.
STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

A4

It is a polymer-based mastic which have feature high filler and bridging. It is highly resistant U.V., sun, and weather, is elastic. Single component. It can be painted. It is long-lasting. It is not flammable. It can adhere to all kinds of surfaces absorbent and dry.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 1,40 ± 0,10

pH (25°C): 7.0 – 9.0

Viscosity (25°C, mPa.s): > 70000

Solid content (% Weight): 74 ± 2

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Crack bridging flexible systems without trafficking ≥ 0.8, with trafficking 1.5 N/mm²

Permeability to water vapour (m): SD < 5 m CLASS I

Solvent : Water

In filling cracks before water based paint and coating,
In dilatation and expansion joints,
In chimney flashing filter sides,
Fuga and joints,
In baseboard, in joint of coatings like stone, ceramic, marble etc.,
Filling or repairing of cracks or holes,
In additional joints of prefabricated gutters and facades

Surface preparation: The surface must be clean and free from factors such as dirt, oil, sludge, etc. that reduce adherence.

Application method: After the ISONEM A4 package is opened, it is mixed for 2 minutes until a homogeneous consistency is obtained. If dilatation or expansion joint is made, it is recommended that PE joint backer rod be placed in the joint before the application is made on it. It is recommended to use joint mesh in chamfer detail applications. ISONEM A4, is ready to use, is filled into the prepared surface by using a spatula or by a mastic pump. After filling, the surface is smoothed with a wet sponge. ISONEM A4 should not be applied more than 5 mm at a time.

PACKING: 5 kg, 10 kg and 18 kg PP in buckets
CONSUMPTION: 30 g for 5 mm and 1 m width
PAINTABLE (COVERAGE) AREA): 120 m.t/18 kg bucket for 10X10 mm
COLOR: White, it can be colored when desired.
SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.
STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

DF 9

ACRYLIC BASED WET ROOM WATERPROOFING,

it is an elastomeric resin based, solvent free, one component acrylic polymer based waterproofing material. It dries on the applied surface and forms a seamless, waterproof and elastic coating. The coating is resistant to high mechanical strength. Tile, ceramic and similar coating should be bonded with a suitable adhesive on the ISONEM DF 9 which high crack bridging capacity.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL) : 1,38 ± 0,10

pH (25°C) : 7.0 – 9.0

Viscosity (25°C, mPa.s) : 9000 - 12000

Solid content (% Weight) : 71 ± 2

Water transmission rate (kg/ m2. h0,5) : < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2) : Crack bridging flexible systems without trafficking ≥ 0.8, with trafficking 1.5 N/mm²

Permeability to water vapour (m) : 5 ≤ SD ≤ 50 CLASS II

Solvent : Water

In wet volumes
Bathroom-shower-restroom
Terrace and balconies
Can be used indoors and outdoors in any kitchen and similar wet areas

Surface preparation: Application surfaces should be dry and clean. Surface reparation and similar pre-insulation should be done before application. 45 g/m² insulation mesh should be used on wall and base joints. If there are residues prevent adherence like dust, dirt etc. on the application surface, they should be cleaned and the insulation and paint primer ISONEM UNIVERSAL PRIMER should be applied to the surface (1: 7 diluted with water;1 part primer, 7 parts water). The primer application should be after a minimum drying time of 4 hours.

Application method: ISONEM DF 9 is ready to use but must be mixed well before use. ISONEM DF 9 is applied by brush in two layers without dilution waiting 4 hours between coats. The insulation application should be protected from water for 24 hours. Do not apply below + 5°C or wet and frozen floors.

COLOR: Blue, white or grey.

CONSUMPTION: 1 kg/m² (two layers application)

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

M 35

It is a single component cement-based super crystalline waterproofing product. It provides insulation deeply by way of applying to concrete surfaces from both negative and positive sides. It reacts with lime particles thanks to inside super gels, produces crystals, and penetrates in-depth to the structure of concrete. It can be applied to new concrete surfaces. It slows down the hydration process on the surface it is applied to and reduces shrinkage crack formation. In addition to waterproofing, it protects concrete against corrosion and diluted chemicals.

TECHNICAL SPECIFICATIONS

pH (25°C): 12.0 – 13.0

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Crack bridging flexible systems without trafficking ≥ 0.8, with trafficking 1.5 N/mm²

Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II

Solvent: Water

Waterproofing of horizontal/vertical floors and walls, internally or externally,
Water tank, wastewater, and other water tanks,
In concrete surfaces exposed to seawater,
In the basement floor and underground insulation,
In the insulation of the basic curtain walls internally or externally,
Irrigation channels and tunnel or dam structures.

Surface preparation: The application surfaces should be dampened previously. The dampening process is made until the surface is saturated 2 hours before starting the application. This process is not necessary if the surface is damp or wet beforehand. The application surfaces should be cleaned from particles such as oil, dirt, mud. If there are segregation, concrete disturbances, and holes, firstly these should be repaired with ISONEM M 03 Elastic Repair Mortar with applying ISONEM D 10 LATEX. Dilatations should be filled with ISONEM A4 elastic filler in advance. The mixture should be prepared after the surface is ready.

Preparation of the mixture: 7 L of clean water is poured into a suitable container. While continuous mixing ISONEM M 35 (20 kg) should be poured slowly and stirring should be continued for 5 minutes. If possible, mix with a 400 rpm drill and mixer. When the mixing process is completed, it is obtained a paint-like mortar that can be applied with a homogeneous brush.

Application method: The application is applied in three coats by brush, wait for 4 hours between the layers. The application should be applied in opposite directions on each layer. The surface should completely close when it is applied to the surface by three layers. The application should not be done in frost and extreme temperatures and should be carried out in cool environments during the evening or early morning. If a frost occurs in cold areas, the floor or wall should be pre-watered with hot water. If the surface will not be covered and the plaster will not be applied after The M 35 application, the application surfaces should be humidified at 48 hours intervals. This process accelerates the curing process and provides more successful insulation.

CONSUMPTION: 2 - 3 kg/m² (three layers application)
PAINTABLE (COVERAGE) AREA: 6 - 10 m²/ Craft bag

PACKING: 20 KG craft bag

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

MS POLIA

ISONEM MS POLIA is a polymer with excellent properties produced in the latest technology. It is ready to use, water-based, polymer-based, UV resistant and elastic structure. It is used as insulation material on the terrace, roofs, concrete, screed, plaster, wood, metal surfaces and surfaces which were applied spray polyurethane thermal insulation. Workmanship is easy and fast.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 1,30 ± 0,10

pH (25°C): 7,0 – 9,0

Viscosity (25°C, mPa.s): 16000 - 18000

Solid content (% Weight): 70 ± 2

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Crack bridging flexible systems without trafficking ≥ 0,8, with trafficking 1,5 N/mm²

Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II

Solvent: Water

Waterproofing of roofs.
Facades
Roofs, woods, decks
On old-based bitumen problematic insulation
Shingle surfaces

Surface Preparation: The surface to be insulated must be clean and dry. Any dirt, mud, rust or oil, must be removed on the surface. It is not used in areas salt efflorescence or places on water flow from the negative side. All cracks and holes should be repaired with ISONEM M 03. Especially in large spans and thermally insulated floors, we recommend applying 45 g/m2 of insulating mesh on floors which are possible to crack.

If there is dilatation in the area to be insulated, dilatation insulation should be made with ISONEM A4 elastic filling and then insulation should be started.Before ISONEM MS POLIA application, ISONEM UNIVERSAL PRIMER (1: 7 diluted with water - 1 part primer, 7 part water) insulation and paint primer should be applied one layer with 100 - 200 g/m2 consumption and then is allowed to dry for 4 hours. The main application should be started after the primer application is waited to dry between 4-6 hours. In steel/metal surfaces, the surfaced should be primed with ISONEM ANTI RUST PRIMER (Anticorrosive primer), consumption of 0,250 - 0,350 kg/m2.

Application Method: ISONEM MS POLIA is ready to use. It should be mixed homogeneously after opening the cover and before application. ISONEM MS POLIA is applied on the primed surface in two layers without dilution at 4 hours intervals. Application should not be made under 5 ° C or on wet and frozen floors. It should be checked whether the correct and sufficient slope is given, especially in applications performed on flat roofs. Care should be taken to ensure that sufficient water drain is available and that there is no ponding of water on the roof or terrace.

CONSUMPTION: 0,8 - 1,0 kg / m² (two layers application)

PAINTABLE (COVERAGE) AREA): 5 kg: min. 5 m2/bucket (two layers application)

10 kg: min. 10 m2/bucket (two layers application)

18 kg: min. 18 m2/bucket (two layers application)

PACKAGING: 5,10, 18 kg in PP Bucket

COLOR: All requested can be produced in colors

STORAGE CONDITIONS / SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages

M 03

It is a cement-based repair mortar with high elasticity, tightness, adhesion strength and not cracking. It is modified with polymer and fiber additives. It is an extremely resisting repair mortar in the applications which is internal tension low and thick. It is used in concrete repairs, ground preparation before waterproofing, the filling of holes and for chamfers.

TECHNICAL SPECIFICATIONS

Compressive strength (Mpa): ≥ 10, SINIF R1

Chloride ion content (%): ≤ 0,05

Adhesive bond (Mpa): ≥ 0,8

Solvent: Water

In surface repairings before waterproofing.
Concrete, plaster and screed repairs.
Filling of the segregation and the rod holes,
In making and repairing construction chamfers.

Surface preparation: Application surfaces must be clean and should be dampened before. If there are residues prevent adherence like free particles, dust, dirt, mud, etc. on the application surface, they should be cleaned. Cracks or segregations to be repaired should be trenched at least 2 cm deep. Before application, we recommend that ISONEM D 10 LATEX (200 mL/m²) is applied absorber surfaces with adhesion problems. When Latex applied surfaces are near dry and slightly sticky, ISONEM M 03 should be applied.

Application method: ISONEM M 03 elastic mortar (20 kg) and 4 L of clean water are mixed homogeneously in a plastic container with a 400 rpm mixer. If mixing process will be manually, it should be made in smaller pieces. ISONEM D 10 LATEX can be added to increase the adherence and water impermeability of ISONEM M 03 elastic mortar. This ratio can be made by adding 1 L ISONEM D 10 LATEX and 3 L water to 20 kg ISONEM M 03. The mixture is applied to the surface by trowel or spraying method. In very hot and very cold weather applications should be paid attention and applications made in extremely hot weather should be humidified at certain intervals

PACKAGING: 20 KG craft bag

CONSUMPTION: 20 kg/m² (for 1 cm plaster) / 1 kg (for 0,5 L space as filling)

PAINTABLE (COVERAGE) AREA: 1 m²/craft bag for 1 cm thick plaster / min. 20 kg/craft for 10 L space as filling

COLOR: Grey

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITION: Store tightly closed in a dry and cool place

L TRANSPARENT POWER

ISONEM L is a water-based pure acrylic new generation transparent waterproofing with excellent adhesion to all surfaces. It is ready to use, UV resistant, glossy and elastic. It is used as a waterproofing material for all kinds of concrete, ceramic, plaster, painted and unpainted surfaces, marble, glass, plastic, metal, tile, stone wall, wood, etc. It is easy and economical to work with.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 1.00 ± 0.10

pH (25°C): 7.0 – 9.0

Viscosity (25°C, mPa.s): 13000 – 15000

Solid content (% by weight): 49 ± 2

Water transfer rate (kg/ m2. h0.5): < 0.1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Crack closure or flexible systems without traffic load ≥ 0.8

Water vapor permeability (m): 5 ≤ SD ≤ 50 CLASS II

Touch dry: 3 hours

Hard dry: 72 hours

Solvent: Water

Fire class: D-s2 d0

Color: Transparent

It can be used on bathroom floors, joints, cracks, window edges, glass, painted walls, plaster, stone walls, wood, shingle and tile roofs, and any surface where transparent waterproofing is required.

Surface Preparation: The substrate must be sound and all surfaces must be cleaned from oil, dirt, and similar residues before application. After opening the package, it should be mixed thoroughly and applied directly to the surface in 2 coats without thinning with a brush, roller, or spray gun. Before application on surfaces such as sheet metal/metal, the surfaces should be primed with ISONEM Anti Rust Primer (Anticorrosive Primer) with a consumption of 0.250 - 0.350 kg/m².

Method of application: ISONEM L is ready for use only after opening the lid and should be mixed homogeneously before application. The glossy surfaces to be applied are applied in 2 coats with a roller and the other surfaces are applied with a brush and a suitable sprayer. It should be allowed 4 hours between coats. The product is suitable for applications between +5°C and +35°C.

Practical considerations: The application surface must be clean and free from dirt, oil, and mud. The product is milky white when applied. After the drying process is completed, it becomes transparent. It is normal to observe white color on the surface in very thick applications. Therefore, it should be applied thoroughly on the surface without thick application.

CONSUMPTION: 0.2 kg/m² (in double application) The consumption values given as approximate and may vary according to the area of the application surface and the application thickness.

PAINTABLE (COVERABLE) AREA: 1 L: 5 m² (two layers of application)

COLOR: Transparent

PACKAGING TYPE: 1 L PP bucket

SHELF LIFE: If stored in original, unopened, and undamaged packaging, the product is safe for use for 24 months from the date of manufacture.

STORAGE CONDITIONS: Store in a dry and cool environment. Store with the package lids tightly closed.

MS 80

It is a siloxane-based transparent insulation product that makes surfaces applied water-impermeable preserving its naturalness, not deform its appearance and texture without forming a film on the absorbent surfaces on which it is applied. Because it does not form a film layer on the surface, it does not prevent, diminish or distort the breathing capacity of the building or stone. Does not make blackening and embossment. Alkali resistance is very high and so can be applied easily in new or old concretes. It prevents efflorescence and staining composed by reason of mortar of press bricks, natural, artificial stone, plasters which it is applied. It prevents the heat insulation value of buildings from being lost since it prevents wetting. Protects the building from corrosion. It also extends the life of structures.

· It is transparent, does not form a film layer, does not distort the natural image, does not give a bright image like varnish.

· In-depth work has a high penetration property

· High alkali resistance.

· Does not prevent structures from breathing.

· Long-lasting and economical.

· Prevents contamination, blackening, and discoloration caused by rain. Protects from frost damage and salt vomiting.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 0,75 ± 0,10

Viscosity (25°C, mPa.s): 0 - 500

Water absorption and resistance to alkali test for hydrophobic impregnation (H): Absorption ratio <7,5 compared with the untreated specimen, absorption ratio (after immersion in alkali solution) <10%

Drying rate for hydrophobic impregnation (H): > 10, CLASS II

Solvent: Organic solvent

It is applied to all kinds of surfaces mineral-based and absorbent. For example; Gross concrete, plaster, brick, briquette, travertine, natural stone, mosaic, gas concrete; tile, etc. It is not applicable to non-absorbent surfaces such as marble, granite, glass, metal, plastic and horizontal absorbent surfaces. ISONEM MS 80 is used to protect the exterior walls of unpainted and absorbent surfaces from rain and its effects.

Surface preparation: Application surfaces must be dry, solid and all kinds of dirt, oil, dust must be cleaned. It should not be applied on wet surfaces. It is ensured that the surface must be dry. The layers that reduce the absorbency of the surface should be cleaned. There should not be cracks larger than 1 mm on the application surface and should be repaired if there is any.

Application method: The application should be at least 2 layers against the top to bottom with the help of a brush, roller or spraying. Before the first layer dry, the second layer should be applied to a wet first layer and it ensures that the surface should be fully saturated. It should not be used flammable material during application. Eye and skin contact should be avoided, gloves and goggles should be used

PACKING: 3,5 L canister

CONSUMPTION: 100 - 200 mL / m² (two layers application)

PAINTABLE (COVERAGE) AREA): 17,5 - 35 m²/3,5 L canister

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place away from heat and fire

MS POLYMER

ISONEM MS POLYMER: ISONEM MS POLYMER is a pure polymer produced using the latest technology and has excellent properties. It is ready to use, UV resistant, glossy, elastic structure. It is used as exterior insulation material on terraces, roofs, balconies, and wet areas, concrete, screed, plaster, wood, metal surfaces, spray polyurethane heat insulation applied surfaces. It is open to light pedestrian traffic and it has quick workmanship.

TECHNICAL SPECIFICATIONS:

Density (25°C, g/mL): 1,00 ± 0,10

pH (25°C): 7.0 – 9.0

Viscosity (25°C, mPa.s): 13000 – 15000

Solid content (% Weight): 46 ± 2

Water transmission rate (kg/m².h^0.5): < 0,1 CLASS W³

Adhesion strength by pull-off test (N/mm²): Crack bridging flexible systems without trafficking ≥ 0.8

Permeability to water vapour (m): 5 ≤ S_D ≤ 50 CLASS II

Solvent: Water

Insulation of terrace roofs and balconies
Facades
Roofs, woods
On old-based bitumen problematic insulation
On asphalt and concrete floors

Surface preparation: The floor must be strong, clean and resistant to load. All surfaces must be cleaned from oil, dirt and similar residues before application. In primer application, ISONEM MS POLYMER is diluted with 200 % water (1 kg MS Polymer:2 kg water) and fed to the surface with a hard brush. The primer should be left to dry for at least 1 hour after application. In steel/metal surfaces, the surfaced should be primed with ISONEM ANTI RUST PRIMER (Anticorrosive primer), consumption of 0,250 - 0,350 kg/m².

Application method: ISONEM MS POLYMER is ready to use. It is applied to the primed surface in two coats with a brush, roller or a suitable sprayer. Waiting time between the coats is at least 4 hours. The product is produced in two types as "winter" and "summer". 18 - 40 °C for summer application, 5 - 17 °C for winter application.

CONSUMPTION: 0,8 - 1 kg/m² (Color, two layers)

0,3 – 0,5 kg/m² (Transparent, two/three layers)

PAINTABLE (COVERAGE) AREA:

Color application:

5 kg: 5 - 6 m²/bucket (two layers)
10 kg: 10 - 12 m²/bucket (two layers)
18 kg: 18 - 22 m²/bucket (two layers)

Transparent application:

5 kg: 10 - 17 m²/bucket (two/three layers)
10 kg: 20 - 33 m²/bucket (two/three layers)
18 kg: 36 - 60 m²/bucket (two/three layers)

COLOR: All requested can be produced in colors.

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

D 10 LATEX

Adherence Enhancer, It is a liquid that is applied by adding to the mortar or applying to the surface in the application of concrete, plaster, screed, cement-based insulation or ceramic, and add the adhesion strength, elasticity, and adherence - enhancing properties to the mortar. It bonds the old or new materials that will come together by forming a super sticky area on the surface applied and provides excellent adhesion. It prevents the formation of cold joints in concrete, plaster and screed applications. It is applied on humid or dry surfaces. It can be used as a primer on highly absorbent surfaces. ISONEM D10 LATEX increases mechanical strength when used as a primer to the surface prior to insulation. Thus, the insulation materials adhere better to the surface and do not flake and swell up. It provides an easy application of mortar by plastify the mortars in which it is used. Prevents rapid drying by increasing the water holding capacity of the mortar. Prevents shrinkage cracks. It increases the abrasion resistance of the mortar and prevents dusting in screed applications. Increases freezing and thawing resistance. Reduces oil and solvent permeability. Improves resistance to chemicals. ISONEM D 10 LATEX is a water-based, acrylic emulsion-based, single component.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 1 ± 0,10

pH (25°C): 7.0 – 9.0

Viscosity (25°C, mPa.s): 500 - 1500

Solid content (% Weight): 18 ± 2

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Crack bridging flexible systems without trafficking ≥ 0.8, with trafficking 1.5 N/mm²

Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II
Solvent: Water

In all kinds of cement mortars,
In plasters and screeds,
In mortars of tiles and ceramic adhesives
Repair mortars, cold joints,
In places where needed adherence in concrete repairs
In pre-plastering applications,
To be used as a primer before waterproofing applications

Surface preparation: The application surfaces should be dry or slightly humid. The moisturizing process should be done until the surface is full. All surfaces must be clean and all impurities that affect the adhesion like dirt, oil, sludge, rust, etc. should be removed. All surfaces must be clean and free of particles. All layers that affect the adhesion like oil, dirt, paint, cement laitance, rust, and salt efflorescence should be cleaned.

Application method

For adherence: ISONEM D10 LATEX is applied to the surface with 200 mL/m² brush without thinning. The mortar or bonding process is done to on it immediately after application, when it is wet, in latest 30 - 40 minutes.

For concrete and mortar additives: It should be used by adding 1 kg/m³ to the water of the mortar in the production of 1 m³ concrete or mortar. In ISONEM M 03 elastic mortars, approximately 1 kg of ISONEM D10 LATEX should be added to a bucket (25kg) and then enough water should be added (4L).

CONSUMPTION: 200 mL/m² (for adherence), 1 L/m3 (for additive)

COLOR: Transparent

PAINTABLE (COVERAGE) AREA): For adherence min. 25 m² /5 L, for additive min. 5 m³/5 L

PACKAGING: 5 L PE can

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

BE 89

ISONEM BE 89 is a 700% elastic liquid bitumen, rubber modified coating. After drying, it forms a waterproof coating on applied surfaces. High elasticity and crack hiding property. Suitable for insulations of old or new roofs and use under the ground, but not affected by underground waters. It strongly adheres to dry or slightly moist surfaces. It does not swell or peel off over time. Resistant to the plant roots. Also suitable for use in garden & terraces.

Technical Specifications

Density (25°C, g/mL) : 1,00 ± 0,10

pH (25°C) : 7,0 – 9,0

Viscosity (25°C, mPa.s) : 53 ± 2

Water transmission rate (kg/ m2. h0,5) : < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2) : Crack bridging flexible systems without trafficking ≥ 0,8

Permeability to water vapour (m) : 5 ≤ SD ≤ 50 CLASS II

Touch-free Drying : 1 hour

Through-dry time : 72 hours

Pot life (23°C) : X

Solvent : Water

Class of fire reaction : B S1 d0

Color : Black

Foundation, shear wall, external walls of the basement,
Covering on old or new terraces or roofs,
In the re-insulation of old bitumen or bitumen surfaces,
On membranes or repairs,
Roof gutters,
In the insulation of concrete pipe, brick, wood, zinc, aerated concrete etc. surfaces,
Protection of all concrete surfaces under the ground against corrosion.

Surface preparation: Application surfaces should be dry or slightly damp. It should not be used in insulations which is from the negative side and on the basement wall where is appeared salt efflorescence. Application surfaces should be cleaned from all kinds of particles, dirt, a bonding agent, dust, mud. Firstly, gap, hole, crack and segregation on the surfaces should be repaired with ISONEM M03 elastic mortar by using ISONEM D10 Latex as bonding agent. If there is dilatation, it should be filled with ISONEM A4 Elastic Filler. As a primer, ISONEM BE 89 is used as diluted with water 1:1. The primer is impregnated to surface via a hard brush and waited to dry completely. For applications on terraces and roofs, R-3 cm chamfer should be applied to the walls and parapet bottom before this process. In terrace and roof applications, it is recommended to lay an insulating mesh of 45 gr/m² and the application should be done with it. There is no need for mesh in the basement.

Application method: Ready to use. It should be mixed homogeneously before application. ISONEM BE 89 is applied by brush or roller without diluting to the surface 2-3 layers and waiting to dry between the layers. The application should be made in perpendicular layers each time. It is recommended to use the 45 g / m² insulation mesh between the floors in terraces and roofs or on floors with high risk of cracking. Application should not be made in high temperatures or frost. In summer, we recommend that the application be done in the morning or evening. It should be ensured that the roofs on which the application will be made are given the correct and sufficient slope for suitable water drainage Suitable water drainage. In order to avoid ponding on the roof. It is recommended to use with grout detail in chamfer applications.

Application : In perpendicular to each layers

Surface humidity : Dry / slightly humid surface

Primer usage : ISONEM BE 89 (diluted)

Primer consumption : 200 - 300 g/m²

Product usage : 3 layers

Product consumption : 1 – 1,5 kg/m²

Paintable (Coverage) Area : 12 - 18 m²/ bucket

Between two coats : 4 hours

Recommended application tools : Roller (synthetic epoxy), brush, spray

Application temperature (°C) : 5 - 35 °C

Things to consider during and after the application: The application surface must be clean and free from all impurities like dirt, oil, and mud.

Other ISONEM products recommended: ISONEM M 03 for segregation and concrete defects and rod holes, ISONEM A4 for dilatations.

IMPORTANT

The surface should be protected from rain, water, mechanical loads and impacts for 24 hours during and after the application.

Packaging & Storage

Packaging : 18 kg PP in buckets

Storage temperature (°C) : 5 - 35 °C

Shelf life : 24 months from date of production if stored in original, unopened, undamaged packages.

Storage condition : Store tightly closed in a dry and cool place.

BD

It penetrates the floor or joints without forming a film on the surface it is applied on and insulates by providing full protection. It is transparent and not damage to the image of the surface. It breathings, non-flammable and not affected by UV, sunlight. It is applied in indoor and outdoor areas in a short time. The workmanship is easy, economical and long-lasting. It can be applied to all kinds of coated, absorbent and waterproofing problem surfaces.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 0,90 ± 0,10

pH (25°C): 7.0 – 9.0

Viscosity (25°C, mPa.s): 0 - 500

Depth of penetration (H): < 10 mm, CLASS I

Water absorption and resistance to alkali test for hydrophobic impregnation (H): Absorption ratio <7,5 compared with the untreated specimen, absorption ratio (after immersion in alkali solution) <10%

Permeability to water vapour (m): > 10, CLASS II

Solvent: Water

It is applied to all kinds of absorbent surfaces such as plaster, concrete, aerated concrete, screed. It is not applicable only on non-absorbent surfaces such as marble, granite, tiles, ceramics, glass, metal, plastic, and vertical absorbent surfaces.

Surface preparation: Firstly, if there are cracks and swollen parts on the surface, they must be repaired and the surface must be cleaned from impurities like dirt, oil, rust. If the joint fillings abraded, they are renewed, the coatings that have bulged or displaced are repaired. If the mastic and silicon applications were peeled off or removed, they must be repaired, and the surface is become fully prepared for the insulating application. If the floor has been washed, it must be let to dry thoroughly and the application should be made after the floor is completely dried.

Application Method: The plastic can of ISONEM BD is shaken thoroughly before usage. Then, the product is poured into a plastic bucket and is thoroughly applied on the surface via a brush. ISONEM BD leaves stains glazed surfaces like ceramic, marble when it dries, because of not absorbed. So it is not suggested on these surfaces and especially it should be applied to joints carefully. The surface where the product has been applied is to let dry for 1 hour. After waiting for one hour, the remains of the product that have not been absorbed are wiped out with a wet piece of cloth. The cleansing operation must be done with a wet piece of cloth and it must be avoided the use of materials such as detergents. The second layer application is done in a maximum of 1 hour before the first layer dry, "wet on wet", repeating the same processes. After an hour, surfaces of ceramics and marbles are wiped with a wet piece of cloth and the second/last layer application is finished.

CONSUMPTION: 200 mL/m²(two layers application)

PAINTABLE (COVERAGE) AREA: Min. 25 m²/5 L PE can

PACKAGING: 5 L PE can

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITION: 5 - 35 °C - Store tightly closed in a dry and cool place

M 36

It is the rapid setting mortar that is ready to use, instantly stopping the water leakages. When it comes into contact with water, it blocks water by setting in 40 seconds. ISONEM M 36 is used in drying active water streams and for surface water. ISONEM M 36 is for preparation for insulation by stopping water. It has high expansion property, does not shrink. It does not contain soda or chlorine, it does not harm the reinforcement and iron, the adherence property is excellent.

TECHNICAL SPECIFICATIONS

Compressive strength (Mpa): ≥ 10, CLASS R1

Chloride ion content (%): ≤ 0,05

Adhesive bond (Mpa): ≥ 0,8

Setting time (sec): 40 - 50

Solvent: Water

Stopping pressurized water,
To stop water leaks before cement-based insulation is applied,
In drying the surface and in the prevention of leakages coming from cracks,

Application method: The application is made in powder form. Rubber gloves should be worn during application. To the prepared surface, a small amount of dust is taken into the palm for the buffer and the material is hand-pressed by hand to the area of the active water leakage. This process is continued until the powder hardens and water is cut off. After the water is stopped, the free material remaining on ISONEM M 36 is cleaned with a dry brush. Then, ISONEM M 35 is applied in three layers to form permanent insulation. If ISONEM M 36 is applied as a mortar, it is mixed with clean water in 2/5 ratio (40%) and put into a paste consistency. This mixture is prepared kneadable without crumbling. This mortar starts to heat up with the reaction and the mortar that is heated is turned into a plug pressed into the hole where the water is released. It is expected to be fully hardened and the hand is held there for a while. As in the dry application, the ISONEM M 35 is applied in three layers and the insulation is completed.

PACKING: 5 kg, 10 kg and 18 kg in PP Bucket

CONSUMPTION

5 kg: min. 2,5 L hole / PP bucket,

10 kg: min. 5 L hole / PP bucket,

18 kg: min. 9 L hole / PP bucket

COLOR: Grey

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

MS 20

It is a special plaster produced for the improvement of humid and damaged walls. The walls absorb to existing water which is loaded various salts like carbonate, sulfate, nitrate from the soil in different seasons via capillary canals and spaces. Then the water absorbed from the soil evaporates and the moisture trace of water and the salts absorbed from the soil remained back. These salts accumulate in the wall and the plaster over time, and when they come back in contact with moisture, they come forth from the wall by popping up the paint and even the plaster. In order to solve this problem, ISONEM MS 20 is made of capillary plaster and water is allowed to evaporate rapidly without any trace of moisture. ISONEM MS 20 contains micro-spaces that store salts and prevent their expansion. It is prevented that the salts damage to the paint and the plaster thanks to these spaces. It prevents swelling due to efflorescence. ISONEM MS 20 is hydrophobic (water repellent). It provides thermal insulation thanks to micro cavities up to 40%.

TECHNICAL SPECIFICATIONS

Water retention rate (%): 98

Capillary water absorption rate (kg/m3): 0,35

Micro-space ratio (%): 34

Water penetration depth (mm): 2

Compressive strength (Mpa): ≥ 10, SINIF R1

Chloride ion content (%): ≤ 0,05

Adhesive bond (Mpa): ≥ 0,8

Solvent: Water

In humid walls such as bathroom, kitchen, basement,
On the walls in contact with soil,
Subbasements and all kinds of paint blistering.

Surface preparation: The surface must be cleaned from old salt-damaged plaster and the cracks and gaps should be filled with ISONEM M03 elastic mortar.

Application method: The salt-damaged plaster layer is completely scraped off by mechanical methods. 4 L water is transferred to a suitable container. It is mixed for 5 minutes until homogenous with a mixer. The application is made in two layers. The first layer is drawn to the surface with a 5 mm thick trowel. The second layer is glued and polished by pulling 2 cm thickness after 24 hours. Paint should be made after 14 days. Breath-taking paints should be preferred when selecting the paint type.

PACKING: 20 KG craft bag

CONSUMPTION: 20 kg/m² (For 2.5 cm thick plaster) - min. 1 m²/ craft bag

COLOR: Grey

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

MD 28

It is a cement-based, two-component, crack bridging capacity and walkable an insulating product having high abrasion resistance. It is applied by brush, has high elasticity. It closes the capillary and shrinkage cracks on the applied surface. It has high adherence. It adheres perfectly to surfaces like concrete, plaster, screed, etc. and does not get removed by time. It is resistant to outdoor weather conditions, UV, mechanical impacts and abrasion. It is water based, acrylic emulsion and cement based, two components.

TECHNICAL SPECIFICATIONS

Density B comp. (25°C, g/mL): 0,90 ± 0,10

pH B comp. (25°C): 7,0 – 9,0

Viscosity B comp. (25°C, mPa.s): 9000 - 12000

Solid content B comp. (% Weight): 48 ± 2

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Crack bridging flexible systems without trafficking ≥ 0,8, with trafficking 1,5 N/mm²

Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II

Pot life (23°C): 30 – 40 minutes

Solvent: Water

Positive insulation of walls and floors,
Insulation of concrete, plaster, and screed,
Balcony, terrace, swimming pools
External curtain wall insulation,
Precast and prefabricated elements, roofs.

Surface preparation: All surfaces should be cleaned from foreign objects like oil, dust, dirt, etc. before the application. The surface must be clean and moist. If there are any segregations, voids or need for repair on the surface, they should be filled with ISONEM M 03 elastic mortar. If there are surfaces with adhesion problems, they should be primed with adherence enhancer ISONEM D 10 LATEX and ISONEM MD 28 should be applied while the surface is slightly sticky and before it is completely dry.

Preparation of the mixture: ISONEM MD 28 consists of two components. The first part is component A consisting of powder polymer and hardener and the second component is liquid component B consisting of liquid polymer. B component (10 kg) in liquid form is placed in a clean, sufficiently large container. A component (20 kg) of powder is slowly added to the continuous mixing liquid with the aid of a mixer and gently mixed so that no lumps remain. Mixing should be continued for 5 minutes. At the end of the mixing, a homogenous, brushable mortar is obtained.

Application method: ISONEM MD 28 should be applied in 3 coats. The application process should be perpendicular layers to each other, homogeneously and smoothly with the help of a brush. The wet film thickness should not exceed 1 mm at one layer. It should be waited a min. of 4 hours between the coats and it should not be interrupted for more than 24 hours. The application should not be done in extreme heat or frost, it should be done in the morning or evening cool. It is recommended to use with grout detail in chamfer applications. Tools used should be cleaned with water at the end of the application.

CONSUMPTION: 2 - 3 kg/m² (three layers application)

PAINTABLE (COVERAGE) AREA):10 - 15 m² /1 set

COLOR: Greenish gray

PACKING: 30 kg set, Component A 20 kg powder craft bag + B Component 10 kg liquid PE drum

STORAGE: 24 months from date of production if stored in original, unopened, undamaged packages. Store tightly closed in a dry and cool place

Product categories

Social media

Contact

Created a website

Waterproofing Products

SB

A4

DF 9

M 35

MS POLIA

M 03

L TRANSPARENT POWER

MS 80

MS POLYMER

D 10 LATEX

BE 89

MS BD

M 36

MS 20

MD 28

Product categories

Social media

Contact

Created a website

SB

A4

DF 9

M 35

MS POLIA

M 03

L TRANSPARENT POWER

MS 80

MS POLYMER

D 10 LATEX

BE 89

BD

M 36

MS 20

MD 28