Special Paints

DIAMOND PAINT

ISONEM DIAMOND PAINT is a special interior and exterior paint which is a water-based, long-lasting, flexible and solid structured, dirt and stain-repellent, washable/wipeable, resistant to all weather conditions, bright and has vivid colors. Thanks to its bright structure, it does not require any extra application such as polish or varnish. It is harmless to health and environmentally friendly. It does not swell and spill, has high covering power and provides a permanent decorative appearance on the interior and exterior of the buildings with glossy and vibrant colors. Thanks to its UV resistance, its colors preserve the vitality and brightness of the first day. It is resistant to moisture and water, and has high alkali and chemical resistance.

FEATURES
· It is odorless and environmentally friendly, does not contain VOCs and solvents.
· It has high elasticity, does not crack.
· Water and moisture resistant, washable.
· Provides a decorative appearance with vivid and bright colors.
· It has high covering power.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 1,20 ± 0,10

pH (25°C): 7,0 – 9,0

Viscosity (25°C, mPa.s): 9500 - 10500

Solid content (% Weight): 50 ± 2

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Crack bridging flexible systems without trafficking ≥ 0,8, with trafficking 1,5 N/mm²

Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II

Solvent: Water

It is used as a bright interior and exterior coating and paint on the exterior and interior facades of buildings, all kinds of walls, jambs, wood and metal surfaces with antirust primer.

Surface preparation: The surface must be firm, clean and dry. All surfaces should be cleaned from oil, dirt and all kinds of residues before application. ISONEM DIAMOND PAINT product itself should be diluted with 200% water and used as a primer on concrete, plastered, previously painted walls (1 kg DIAMOND PAINT, 2 kg Water). The prepared primer is fed to the surface with a stiff brush. After the primer application, it should be left to dry for at least 1 hour. Before application on surfaces such as sheet/metal, the surface should be primed with ISONEM Anti Rust Primer (Anticorrosive Primer) with consumption of 0.250 - 0.350 kg / m².

Application method: ISONEM DIAMOND PAINT is ready to use, it can be used by diluting with 10% water if a smooth appearance is desired in interior and exterior applications, and should be used without dilution for textured appearance. It is applied on the primed surface in two layers with a brush, roller or a suitable sprayer. Waiting time between coats is at least 4 hours.

CONSUMPTION: 200 - 500 g/m² (2 Layers, It may vary depending on the nature of the application surface and the pattern roll to be applied.)

PAINTABLE (COVERAGE) AREA: 10 kg: 20 - 50 m²/ bucket (Two layers application)

18 kg: 36 - 90 m²/ bucket (Two layers application)

COLOR: Can be produced in all desired colors.

PACKING: 5 kg, 10 kg,18 kg PP in buckets

SHELF LIFE: 24 months from the date of production if stored in original, unopened and undamaged packages.

STORAGE CONDITIONS: Store in a dry and cool place with the package covers tightly closed.

EP PRIMER

Two-Component Solvent Free Epoxy Resin Based Primer

SOLVENT FREE EPOXY PRIMER, it is transparent, hygienic primer material. It is easy to apply, it has perfect adherence. It is epoxy resin base, solvent-free, two component. It has very good penetration, low viscosity and moisture tolerance. It increases the concrete strength by filling the capillary cavities of the concrete floors and acts as an adherence bridge for the epoxy or polyurethane topcoat paints and coatings.

TECHNICAL SPECIFICATIONS

Density A comp. (25°C, g/mL): 0,90 ± 0,10
Viscosity B comp. (25°C, mPa.s): 0 - 500
Solid content (% Weight): 100
Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3
Adhesion strength by pull-off test (N/mm2): Rigid system without trafficking ≥ 1.0 N/mm², with trafficking ≥ 2,0 N/mm2
Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II
Pot life (23°C): 30 - 40 minutes
Solvent: Organic solvent

Surface preparation: All free loose material must be removed from the surface. All oil and dirt on the surface should be cleaned by blasting with sandblasting. The temperature of the surface should be + 3°C above the dew point when the application is done.

Mixture preparation: ISONEM EP PRIMER is supplied in ready-to-use kits according to the mixing ratio. The mixture should be prepared to be enough amount for application by taking into account the life of the mixture. Before starting mixing, ensure that the material temperatures are between 15 and 25°C. Component A should be thoroughly mixed with a mixer at 300 - 400 rpm for 2 - 3 minutes without entraining air. Subsequently, all of component B must be poured into component A and ensure that there is no material left inside the B component. Mix for at least 4 minutes until a homogeneous mixture is obtained and the prepared mixture should be consumed within 30 - 40 minutes.

Application method: ISONEM EP PRIMER should be applied with brush or roller in order to obtain the desired thickness. When the mixture is got the suitable consistency, if it is necessary, the air of the application should be removed via spiked roller.

CONSUMPTION: 0,25 - 0,4 kg/m²

PAINTABLE (COVERAGE) AREA: 12,5 - 20 m² /5 kg set, 2 - 3,2 m² /0,8 kg set

COLOR: A component transparent, B component brown

PACKAGING:
2 kg set (Component A: 1,25 kg can, Component B: 0,75 kg can)
5 kg set (Component A: 3,1 kg can, Component B: 1.9 kg can)

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place

POOL

Polyurethane Based, 2 Components Pool Paint, it is the swimming pool paint which is polyurethane resin based, consisting of two components, blue in color. It is not affected by water and water pressure. ISONEM POOL is particularly very ideal to use in swimming pools, newly made decorative pools in the cases where the ceramic covering will not use. It gives a homogeneous blue appearance on the surface applied. It is elastic, not crack, it is not affected by the UV lights and the swimming pool chemicals. The product has high resistance against alkali and chloride. Its color does not fade in time, not destroyed underwater, abrasion-proofing. The workmanship is very easy and economic.

TECHNICAL SPECIFICATIONS

Density A comp. (25°C, g/mL): 1,25 ± 0,10

Viscosity A comp. (25°C, mPa.s): 1000 - 3000

Solid content (% Weight): 67 ± 2

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Rigid system without trafficking ≥ 1.0 N/mm²

Permeability to water vapour (m): SD ≤ 5 CLASS I

Pot life (23°C): 5 - 6 Hours

Solvent: Organic solvent

· In pools, water tanks, water reservoir, purification and balance tanks,

· In metal tanks and water cisterns,

· In ornamental ponds, ponds, dams, water channels,

· On concrete, plaster, and screed.

Surface preparation: The surface to be coated must be clean, dry and all impurities that can affect the adhesion like dirt, oil, loose paint or foreign material must be cleaned. Surface repairs, cracks, and gaps should be repaired with ISONEM M 03 Elastic Repair Mortar. Before application of ISONEM POOL, in concrete, marble, granite, raw wood, tile, ceramic etc. surfaces, ISONEM EP PRIMER should be used as a primer with 0,250 - 0,400 kg/m² consumption. In steel/metal surfaces, the surfaced should be primed with ISONEM ANTI RUST PRIMER (Anticorrosive primer), consumption of 0,250 - 0,350 kg/m².

Preparation of the mixing: To prepare ISONEM POOL for use, first stir the contents of the A Component (Paint) and then add the contents of the B Component (Hardener) and mix homogeneously for 3 - 4 minutes to ensure thorough mixing.
Application method: It should be applied with a brush, roller or appropriate spray and left to dry. The second layer should be applied after the first coat is dried, in 24 hours. The prepared mixture should be consumed in 5 - 6 hours. After the application, the pool should be left to curing 10 days, before filling water

CONSUMPTION: 1 kg/m² (two layers) | min. 4,5 m² /set (two layers)

COLOR: Blue. You can consult our company for other color demands.

PACKAGING: 4,5 kg set (Component A: 4 kg paint, Component B: 0,5 kg hardener)

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place away from heat and fire.

THERMAL PAINT

ISONEM THERMAL PAINT is an elastomeric resin-based, contains special vacuum microspheres, have vapor-permeability, water-based, a low thermal conductivity, high sunlight absorbency, and high surface heat transmission value. Its activity is scientifically proved special insulating paint which provides the thermal and water insulation in the interior and exterior facades. It provides energy savings to buildings of up to 40% depending on the application layers number in heating and cooling energy costs. When the ISONEM THERMAL PAINT with special vacuum microspheres is used as interior wall paint, it reflects the radiant heat generated inside to the interior environment, and when it is used on the exterior, the incoming radiant heat is reflected back to the outside. When used on roofs, it reflects a minimum 80% of the sun's rays thanks to its ceramic-reinforced formula. While the water never passes from the film surface applied Isonem Thermal Paint, the moisture inside the building evaporates away from the structure.

VIDEO

PROPERTIES

· Radiont heat proof.

· Saves up to 40% energy.

· Applicable to internal and external surfaces.

· Labor costs are low and easy to apply.

· It prevents the formation of moisture and mold in the wall.

· It has water and sound insulation feature.

· It has late flammability and nonflammability.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 0,70 ± 0,15

pH (25°C): 7.0 – 9.0

Solid content (% Weight): 45 ± 2

Solid content (% Volume): 65 ± 2

Water transmission rate (kg/ m². h^0,5): < 0,1 CLASS W₃

Adhesion strength by pull-off test (N/mm²): Crack bridging flexible systems without trafficking ≥ 0.8

Permeability to water vapour (m): 5 ≤ S_D ≤ 50 CLASS II

Certification: TSE K 127 THERMAL PAINT

Class: COLD CLIMATE PAINT

Brightness: N/A (not applied)

Wet abrasion resistance (μm): CLASS II

Covering power (m²/L): CLASS I

Dry film thickness: CLASS E₅

Grain size: CLASS S₂

Crack covering feature (μm): not required, CLASS A0

Carbon dioxide permeability (g/m².d): not required, CLASS CO

Surface heat transmission value (ε): min. 0.80

Sunlight absorbency value (α): 0.820, min. 0.80

Thermal paint surface resistance (RS): 0.0495 ± 1,5 %

Heat conductivity coefficient (W/mK): 0.023, λ<0.060

Impact resistance: No cracking & rupture

Solvent: Water

Surface preparation: Surfaces to be applied should be free of dirt, oil, paste, grease, loose parts and other foreign materials. The appropriate primer selection for surface is made according to the following table. ISONEM UNIVERSAL PRIMER (1: 7 diluted with water - 1 part primer, 7 part water) insulation and paint primer should be applied one layer with 100 - 200 g/m² consumption. The primer is then allowed to dry for 4 hours.In steel/metal surfaces, the surfaced should be primed with ISONEM ANTI RUST PRIMER (Anticorrosive primer), consumption of 0,250 - 0,350 kg/m².

Application method: ISONEM THERMAL PAINT must be mixed thoroughly before use.In exterior applications, 2 to 3 coats can be applied by roller or brush without diluting the product. In interior applications, it should be applied as 1 or 2 coats according to color and hiding power. It is recommended to apply 2 - 3 coats in roof applications. It is recommended that each coat be painted perpendicular to the previous coat. It can be applied by taking into consideration the drying processes. The second and third layer should be applied after the first layer has dried. Wait for 4 hours between two coats.

COLOR: All requested can be produced in colors

PACKING: 5 L, 10 L and 18 L PP bucket.

CONSUMPTION: max. 300 mL/m² (in interior applications), 1 L/m² (for 1 mm thickness), 2 L/m² (for 2 mm thickness) in exterior applications

PAINTABLE (COVERAGE) AREA: 5 L: 2,5 - 5 m²/bucket, 10 L: 5 - 10 m²/bucket, 18 L: 9 - 18 m²/bucket

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

IMPORTANT: Consuming more or less can lead to inefficiency and side effects.

The surface should be protected from rain, water, mechanical loads and impacts for 24 hours during and after the application

BE 99

Elastic, Waterproof Exterior Wall Paint

ISONEM BE 99 It is a paint that forms a seamless, elastic and waterproof layer by drying on the surface on which it is applied. It creates a decorative coating. It is water-based polymer-based, solvent-free and has 300% elasticity. It can be applied on dry or slightly moist surfaces. It is resistant to UV and outdoor weather conditions. It is water-impermeable but has a water vapor permeable structure. It provides the buildings to breathe and prevents moisture, damp with this feature. Thanks to its special formula, it does not keep dirt and preserves its first-day feature for many years. It prevents the carbon dioxide gas formed in the structure and thus protects the equipment in the concrete by reducing the formation of carbonization. It protects the buildings against the effects of rain, dirt, traffic etc. from the external environment. Since it has high elasticity, it is not affected by cracks that may occur on the building surface.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 1,40 ± 0,10

pH (25°C): 7,0 - 9,0

Viscosity (25°C, mPa.s): 28000 – 32000

Solid content (% Weight): 79 ± 2
Water transmission rate (kg/ m². h^0,5): < 0,1 CLASS W₃

Adhesion strength by pull-off test (N/mm²): Crack bridging flexible systems without trafficking ≥ 0.8, with trafficking 1.5 N/mm²

Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II

Solvent: Water

All kinds of plaster and painted exterior surfaces,
Mineral render etc. on old coatings,
Exterior surfaces, wood, etc.
In buildings covered with thermal insulation systems,
For the painting of concrete or prefabricated structures,

Surface preparation: Before application, the surfaces must be clean, free of oil, dirt, mud and loose parts should be cleaned. The surface may be dry or slightly humid. It should not be applied on surfaces with salt efflorescence from the negative side. If the application surface has cracks, holes, etc., these should be repaired with ISONEM M 03 elastic mortar. If dilatation is present on the surface, it should be filled with ISONEM A 4 elastic filler in advance. Before ISONEM BE 99 application, ISONEM UNIVERSAL PRIMER (1: 7 diluted with water - 1 part primer, 7 part water) insulation and paint primer should be applied one layer with 100 - 200 g/m² consumption and then is allowed to dry for 4 hours. In steel/metal surfaces, the surfaced should be primed with ISONEM Anti Rust Primer (Anticorrosive primer), consumption of 0,250 - 0,350 kg/m².

Application method: ISONEM BE 99 is ready to use. We recommend that the product is mixed homogeneously before using it. The application can be made with a brush, roller or a suitable sprayer. After the primer application, ISONEM BE 99 is applied to the surface by two coats, waiting between the coats at least 4 hours and the painting process is finished

CONSUMPTION: 0,5 - 1 kg/m² (It may vary depending on the colors, the properties of the application surface and the pattern roll to be applied.)

PAINTABLE (COVERAGE) AREA
5 kg: 5 - 10 m²/bucket
10 kg: 10 - 20 m²/ bucket
18 kg: 18 - 36 m²/ bucket

COLOR: All requested can be produced in colors.

PACKING: 5 kg, 10 kg and 18 kg PP buckets

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place

ANTI SOUND PAINT

Sound Insulation Paint

ANTI SOUND PAINT, it is an acoustical paint for damping and blocking of noise that is designed to absorb and isolate sound in the best way. According to TS 140-4 Standard, in the results of the measurement and analysis, the applied paint, in 1/3 octave frequency in terms of dB, according to 100 Hz till 50 dB it has been certified by the Turkak approved accredited laboratories where it has reduced and absorbed the sound. Water-based and single-component ANTI SOUND PAINT can be produced in desired colors. Besides sound insulation, it is resistant to fire due to its late inflammability and non-flammable properties. It is water based, acrylic emulsion-based, one component. It can be used as interior and exterior sound insulation paint in all places where noise is not desired.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 0,80 ± 0.10

pH (25°C): 7.0 - 9.0

Viscosity (25°C, mPa.s): 12500 - 13500

Solid Content (% Weight): 53 ± 2

Water transmission rate (kg/ m2. h0,5 ): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Crack bridging flexible systems without trafficking ≥ 0.8

Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II

· In apartments, hospitals and hotels, schools, nurseries,

· In engine and engine rooms,

· In entertainment venues, cinema and theater halls,

· Vehicle and yachts, military facilities, shooting ranges.

Surface preparation: Before application, the surfaces must be clean, free of oil, dirt, mud and loose parts should be cleaned. Before ISONEM ANTI SOUND PAINT application, ISONEM UNIVERSAL PRIMER (1: 7 diluted with water - 1 part primer, 7 part water) insulation and paint primer should be applied one layer with 100 - 200 g/m² consumption and then is allowed to dry for 4 hours. In steel/metal surfaces, the surfaced should be primed with ISONEM Anti Rust Primer (Anticorrosive primer), consumption of 0,250 - 0,350 kg/m².

Application method: ISONEM ANTI SOUND PAINT is easily applied by roller, brush or spray. The product should be mixed homogeneously before using it. Then it is applied in layers of 1 - 2 mm at 4-hour intervals. In the interior wall applications which it is not wanted pattern, we recommend that the application should be with an epoxy roller.

COLOR: All requested can be produced in colors.

PACKING: 18 L PP bucket.

PAINTABLE (COVERAGE) AREA: 9 - 18 m²/bucket.

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

ANTI FIRE PAINT

FIRE RETARDANT TOP COAT PAINT, It is a topcoat paint which is fire retardant, non-flammable, forms a whole layer with drying on the surface on which it is applied. It is flame retardant in direct contact with fire. Resistant to fire. It is water-based and solvent-free. It is elastic, unaffected by movements. It can be easily applied to dry or slightly humid surfaces. It is water-impermeable but water vapor permeable. Thanks to this feature, it does not prevent the breathing of the surface. It doesn't keep dirt for long years via its special formula. It is suitable for use in wood, concrete, prefabricated and steel structures.

TECHNICAL SPECIFICATIONS

pH (25°C): 7.0 - 9.0

Viscosity (25°C, mPa.s): 12000 - 15000

Density (25°C, g/mL): 1.40 ± 0.10

Solid Content (% Weight): 76 ± 2

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W₃

Adhesion strength by pull-off test (N/mm2): Crack bridging flexible systems without trafficking ≥ 0.8

Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II

Solvent: Water

RESULT: ISONEM ANTI FIRE PAINT '' fireproof paint '' test on TS EN 13823: MARCH 2010 standard in TS EN ISO 11925-2 on 02.2012 / 139921 as a result of the test and the test result TS EN 13501-1 / JANUARY 2010 Table B Complies with S1 class d0 criteria.

ACCORDING TO THE TEST RESULT OF TSE EXPERIMENT AND CALIBRATION CENTER PRESIDENCY EX LABORATORY; Reaction of the experiment sample to fire in EN 13501-1 B (in accordance with the European classification) test method: PASSED. In the test method according to the TS EN ISO 11925-2 of the experiment sample;

· Ignition of samples: DID NOT OCCUR

· 150 mm measuring line during the flame test period: DID NOT REACH

· Dripping of samples: DID NOT OCCUR

· Filter paper: DID NOT BURN

· Experiment sample just: MELTED

· Lateral fire spread on the longitude: DID NOT OCCUR

· Fire particles or drops f <10s and f >10s: DID NOT OCCUR

· Smoke spread from the sample into the room: DID NOT OCCUR

SUMMARY OF TSE TEST RESULTS

· Average FIGRA value (W/s): 17,24

· Average THR600s (MJ): 0,93

· Value of average SMORA (m²/s²): 10,58

· Average TSP600s (m): 51,86

· Up to LFS line (mm): DID NOT OCCUR

· Burning drops/particles ≤10s: DID NOT OCCUR

· Burning drops/particles > 10s: DID NOT OCCUR

· All kinds of plastered, painted and unpainted interior and exterior surfaces

· Concrete, wood and steel structures

· In roofs, in fire steps

· In all places where nonflammability is desired

· In schools, kindergartens, hospitals, theaters, and theaters

· Plasterboard wall partitions and ceilings

· Thermal power plants and industrial buildings, factories

· Military facilities

Surface preparation: It is used as protective topcoat on surface which is applied ISONEM ANTIFIRE PAINT PLUS. ISONEM ANTIFIRE PAINT is applied single layer with 0.3 - 0.5 kg/m² consumption for topcoat application. If it is desired to be used as a flame retardant, surfaces should be clean before application, there be cleaned from impurities like dirt, oil, rust and, shield particles should be cleared. ISONEM UNIVERSAL PRIMER (1: 7 diluted with water - 1 part primer, 7 part water) insulation and paint primer should be applied one layer with 100 - 200 g/m² consumption. The primer is then allowed to dry for 4 hours. In steel/metal surfaces, the surfaced should be primed with ISONEM Anti Rust Primer (Anticorrosive primer), consumption of 0,250 - 0,350 kg/m².

Application : It can be made with a brush, roller, or a suitable sprayer. The product should be mixed homogeneously before use and applied on the surface in two coats without reconstitution at 4 hours intervals

CONSUMPTION: 0,6 - 1 kg/m² (2 Layers)

PAINTABLE (COVERAGE) AREA: 5 kg: min. 5 m²/bucket (two layers application), 10 kg: min. 10 m²/bucket (two layers application), 18 kg: min. 18 m²/bucket (two layers application)

COLOR: All requested can be produced in colors.

PACKING: 5,10,18 kg PP in bucket

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

IMPORTANT: The surface should be protected from rain, water, mechanical loads and impacts for 24 hours during and after the application

POOL TRANSPARENT

ISONEM Pool Transparent is a two-component, modified polyurethane resin-based, transparent pool paint designed to waterproof ceramic, tile, glass mosaic-coated surfaces with insulation problems. Ceramic, tile, glass mosaic, tile, etc. can be used to solve the insulation problems of existing pools. The product, which provides waterproofing in an extremely easy and economical way without the need to remove the coatings, gives the surface a bright appearance as well as excellent insulation on the surface it is applied. It is hard-elastic, does not crack, does not swell, does not lift. It is not affected by UV rays and pool chemicals. It is extremely resistant to alkali and chlorine. It does not turn yellow, does not deteriorate under water, does not corrode. It is extremely easy and economical to work.

TECHNICAL SPECIFICATIONS

Density A comp. (25°C, g/mL): 0,93 ± 0,10

Solid content (% Weight): 30 ± 2

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Rigid system without trafficking ≥ 1.0 N/mm²

Permeability to water vapour (m): SD ≤ 5 CLASS I

Pot life (23°C): 5 - 6 hours

Solvent: Organic solvent

Ceramic, tile, glass mosaic, tile, etc. covered swimming pools,
In ornamental pools,
Hammam, sauna, etc. in places,

Surface preparation: The surface must be clean, dry and free of foreign materials such as dirt, oil, coating, surface curing materials. After the water of the existing pools in use is drained, at least 7 days should be waited before the application in order to ensure that the joints are completely dry. If the existing joint fillers are worn, the necessary repairs and renewals must be made with cement-based joint fillers and full curing should be expected. Primer should be applied to the pre-prepared application surface before ISONEM POOL TRANSPARENT application, and ISONEM LIQUID GLASS product should be used in a single layer with a consumption of 75 – 100 g/m2 in the primer application. 4 hours after the primer application, ISONEM POOL TRANSPARENT, which is the last layer, should be applied.
Preparation of the mixing: Before preparing the mixture, mix component A until it becomes homogeneous in itself. After adding component B to component A, mix for 3-4 minutes until a homogeneous mixture is obtained.

Application method: The application should be done in one coat, with a brush, roller or a suitable sprayer. The prepared mixture should be consumed within 5-6 hours. After the application, the pool should be left to cure for 10 days before being filled with water

CONSUMPTION: 100 - 200 g/m²

PAINTABLE (COVERAGE) AREA): 22,5 - 45 m² /set

COLOR: Transparent

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

ANTI FIRE PAINT PLUS

It is a fire-retardant, water based paint that is developed for the protection of the buildings from fire and is fire retardant in the intumescent structure that provides fire insulation via expanding. It forms a seamless layer by drying on the surface on which it is applied. It has excellent flame retardant property, it expands via reacts chemically at the time of the fire and prevents the surface temperature from rising to critical levels. It is water vapor is permeable. Thanks to this feature, it does not prevent the breathing of the surface. It is suitable for use in wood, concrete, prefabricated and steel structures.

TECHNICAL SPECIFICATIONS

pH (25°C): 7.0 - 9.0

Viscosity (25°C, mPa.s): 10000 - 12000

Density (25°C, g/mL): 1,15 ± 0.10

Solid Content (% Weight): 64 ± 2

Solid Content (% Volume): 55 ± 2

Water transmission rate (kg/ m2. h0,5 ) : < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2) : Crack bridging flexible systems without trafficking ≥ 0.8

Permeability to water vapour (m) : 5 ≤ SD ≤ 50 CLASS II

Solvent: Water

Applied Standard: EFECTIS ERA EURASIA Testing and Certification Inc. which is accredited by TURKAK, TSE 13501-2: 2016 Fire classification of construction products and building elements - Part 2: Classification using data obtained from fire resistance tests (except ventilation installations). According to the results of the inspection and test report 20.05.2019 dated/EEA-19-063 numbered, in accordance with this standard / TS EN 13381-8: 2013 Test Method for Determination of the Contribution of Structural Components to Fire Resistance - Part 8: According to the test results of Test Method of Reactive Protection Applied to Steel Elements,

Fire Resistance Classes: R15-R20-R30-R45-R60-R90.

ACCORDING TO THE TEST RESULTS OF EFECTIS ERA AVRASYA Test and Certification Inc.; Main Layer Paint (intumescent paint): According to ISONEM ANTI FIRE PAINT PLUS TÜRKAK Accredited Test Report, the results of the evaluation can be applied to all other steel classes and the limitations given here, as specified in EN 10025-1, as specified in Article 6.1 of 13251-4. The results of the assessment can also be applied to fabricated sections. Cross-section factors should be determined according to EN 13381-8: 2013 standard. The results of this assessment are valid for the following conditions of three or four environmental protections.

Cross-section factor: 65 m-1 < Am/V < 527 m-1

Thickness: 1,5 mm < dp < 8,6 mm

Design temperature: 300°C < Qa < 750 °C

Section shape: I, H columns and beams

· All kinds of plastered, painted and unpainted interior and exterior surfaces

· In concrete, wooden and steel structures

· Roofs, chimneys, fire escape

· In all places where nonflammability is desired

· In schools, kindergartens, hospitals, theaters, and theaters

· Plasterboard wall partitions and ceilings

· Thermal power plants and industrial buildings, factories

· Military Installations

Surface preparation: Surfaces must be clean and dry before application. Oil, dirt, sludge, such as materials should be cleaned, shield particles should be cleaned. The appropriate primer selection depending on the surface is made according to the following table. ISONEM UNIVERSAL PRIMER (1: 7 diluted with water - 1 part primer, 7 part water) insulation and paint primer should be applied one layer with 100 - 200 g/m² consumption. The primer is then allowed to dry for 4 hours. In steel/metal surfaces, the surfaced should be primed with ISONEM Anti Rust Primer (Anticorrosive primer), consumption of 0,250 - 0,350 kg/m².

Application method: It can be made by brush, roller or a suitable sprayer. It should be mixed until homogenous before use. After the application of primer, it is applied to the surface in two coats 4 hours apart without diluted and the painting process is nished. In exterior applications and in indoor applications that are exposed to water, and high humidity, ISONEM ANTI FIRE PAINT is applied as a topcoat with a brush, roller or a suitable sprayer with consumption of 0.3-0.5 kg/m². In steel/metal surfaces, the surfaced should be primed with ISONEM Anti Rust Primer (Anticorrosive primer), consumption of 0,250 - 0,350 kg/m².

COLOR: All requested can be produced in colors.

CONSUMPTION: 3,5 kg/m² for 1,5 mm thickness, steel structures (Surface / material thickness / depending on the desired fire retardant resistance time vary)

PAINTABLE (COVERAGE) AREA: 3,5 - 5 m²/5 kg bucket, 7 - 5 m²/10 kg bucket, 12,5 - 18 m²/18 kg bucket

PACKING: 5,10,18 kg PP in bucket.

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

IMPORTANT: The surface should be protected from rain, water, mechanical loads and impacts for 24 hours during and after the application.

WRITE & ERASE VARNISH

WRITE & ERASE VARNISH, it is a water-based two - component varnish that allows you to use the desired surface as a whiteboard area with marker pens. Thanks to its transparent structure, it can be used in walls, desks, doors, cabinets, meeting rooms etc. converts it to a writable, erasable format without changing the color of the surface when applied. It is nature-friendly, does not contain VOC and solvent, it is extremely simple to apply. The paint and stains graffiti can be easily removed from the surface applied ISONEM WRITE & ERASE VARNISH. There is no other system that provides this easy cleaning and gives you the opportunity to clean the surface repeatedly without damaging the coating.

TECHNICAL SPECIFICATIONS

Density (A comp, 25°C g/mL): 1,00 ± 0,10

pH (25°C, g/mL): 7,0 - 9,0

Viscosity A comp. (25°C, mPa.s): 0 - 500

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Rigid system without trafficking ≥ 1.0 N/mm²

Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II

Pot life (25°C): 50 - 60 minutes

· Walls, desks, and tables of schools and classes
· Walls of meeting rooms, training and seminar halls,
· Walls of office rooms,
· Road walls,
· Walls of houses, hotels, conference halls,

Surface preparation: Application surfaces should be cleaned from all kinds of oil, dirt, dust and surface residues and must be completely dry and clean.

Preparation of the mixture: ISONEM WRITE & ERASE VARNISH is supplied in ready-to-use kits according to the mixing ratio. The mixture should be prepared to be applied according to the life of the mixture. Before commencing mixing, ensure that the material temperatures are between 15 - 25°C. Component A should be mixed thoroughly with a mechanical mixer at 300 - 400 rpm for 3 - 4 minutes without dragging air in it. Then, all component B must be poured into component A and make sure that there is no material left inside the B component. A + B should be mixed for at least 3 minutes until a homogeneous mixture is obtained and the prepared mixture should be consumed within 50 - 60 minutes.

Application method: ISONEM WRITE & ERASE VARNISH should be applied with the help of brush or roller in order to obtain the desired thickness. It should be applied as 2 or 3 layers and waited for 6 – 8 hours for each coat. Wait at least 3 days before writing/erasing. Text/drawings can be erased with a board eraser. Any non-removable stains need to be cleaned with a wet cloth, other cleaning materials should not be used like detergent, bleach, etc.

COLOR: Transparent

CONSUMPTION: 0,200 – 0,300 kg/m² (2 Layers application)

PAINTABLE (COVERAGE) AREA: 5 - 7,5 m²/set

PACKAGING: 1,5 kg set (Component A: 1,0 kg, Component B: 0,5 kg)

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

ANTI FIRE WOOD VARNISH

ISONEM ANTI FIRE WOOF VARNISH is a fire-resistant, water-based, intumescent and transparent thin-film coating used for the protection of the wooden surfaces in the interior against fire. The Antifire Wood Varnish applied surfaces must be protected by ISONEM LIQUID GLASS liquid glass application from water and humidity. Thanks to its transparent structure, when applied, it provides a surface with a highly fire-retardant performance without changing the color of the surface. If a different color is desired, a coloring agent may be applied to the surface before the application. It is environmentally friendly. It does not contain VOC and solvent, it is extremely simple to apply.

FEATURES / ADVANTAGES

Water-based, environmentally friendly.
Prevents spreading of the flame on the wooden surface.
With its superior fire-retardant performance, prevents the wood from being ignited immediately.
Slows down the speed of fire progress.
Does not emit toxic fumes.
Provides additional safety against fire in closed and risky places where people are gathered.
Easy to using. It can be applied with a spray/brush/roll.

TECHNICAL SPECIFICATIONS

Density A+B comp. (25°C, g/mL): 1,27 ± 0,10

Viscosity A+B comp. (25°C, mPa.s): 1500 - 2500

Pot life (23°C): 30 minutes

Solvent: Water

· Raw wood surfaces, wooden doors

· Interior furniture,

· Historical monuments, finished wooden buildings,

· Hotels, theaters, entertainment venues, computer rooms, and other public facilities.

Surface preparation: Application surfaces should be cleaned from all kinds of oil, dirt, dust and surface wastes and must be completely dry and clean. Primer application is recommended on highly absorbent and exposed surfaces such as raw wood. For primer application, ISONEM LIQUID GLASS product is used with a consumption of 75 - 100 g/m².

Preparation of mixture: ISONEM ANTI FIRE WOOD VARNISH is supplied in ready-to-use kits according to the mixing ratio. Prepare an amount of mixture to be applied by considering the mixture life. Before starting to mix, make sure that temperatures of the materials are between +15 and +25°C. Stir component A with a 300 – 400 rpm mechanical mixer for 3-4 minutes without dragging air in it. Then, pour the entire component B into component A and make sure that no material is left in component B. Stir component A and B at least for 3 min. until a homogenous mixture is obtained and consume the prepared mixture within 40-45 minutes.

Application Method: ISONEM ANTI FIRE WOOD VARNISH should be applied by brush, roller or spray to obtain the desired thickness, it should be applied as 2 or 3 coats, wait for 18 - 24 hours for each coat. ISONEM ANTIFIRE WOOD VARNISH is not water and moisture resistant. Therefore, after the product fully dry, the following day should be applied as a solvent-based ISONEM LIQUID GLASS protective topcoat in 2 coats and waiting for a minimum of 4 hours between coats

CONSUMPTION: 0,3 - 0,5 kg/m² (2 layers)

PAINTABLE (COVERAGE) AREA: 3 - 5 m² /set

PACKING: 1,5 kg set - Component A 1 kg can + Component B 0.5 kg can (hardener)

SHELF LIFE: 6 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

UNIVERSAL PRIMER

ACRYLIC EMULSION BASED CONCENTRATE PRIMER, water-based, one component, transparent, suitable using for inner and outer surfaces is a universal primer.

FEATURES

It penetrates the surface very well. By preparing a strong surface, it connects the top coat paint to the surface, reduces the paint consumption and reduces the water absorbency of the plasters. It is a primer that also has a high adhesion performance in water-based waterproofing materials and wall putty applications.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 1,00 ± 0,10

pH (25°C): 7.0 – 9.0

Viscosity (25°C, mPa.s): 8000 - 10000

Solid content (% Weight): 50 ± 2

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Crack bridging flexible systems without trafficking ≥ 0.8, with trafficking ≥ 1.5 N/mm²

Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II

Solvent: Water

· Concrete, aerated concrete, plaster, and similar raw walls,
· Old lime whitewashed, emulsion-based old interior and exterior painted surfaces are used.

Surface preparation: Before application, swollen, loose and unhealthy looking surfaces should be scrapped, oil and dirt should be wiped off with water. If the salt release continues on the surface, the application should not be carried out until the causes are eliminated

Application method: ISONEM UNIVERSAL PRIMER is mixed thoroughly until it is homogenous before use, and diluted with water 7 times by volume. It is impregnated to the surface by brush or roller as a single layer. It should wait for a primer drying time minimum of 4 hours for the topcoat paint or insulation product application and it should be done in 4-6 hours.

COLOR: Transparent

CONSUMPTION: 100 - 200 g/m² (diluted, variable according to the absorbency of the surface.)

PAINTABLE (COVERAGE) AREA: 40 - 80 m²/ 1 kg, 200 - 400 m²/ 5 kg, 400 - 800 m²/ 10 kg, 600 - 1200 m²/ 15 kg

PACKING: 1 kg, 5 kg, 10 kg and 15 kg PP Buckets.

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place

ANTI RUST PRIMER

ANTI RUST PRIMER, is an epoxy resin-based anticorrosive primer that is applied directly to all metal surfaces and protects the surface it is applied against corrosion thanks to its high anticorrosive structure. In addition to excellent adhesion, it dries quickly and is easy to work with.

TECHNICAL SPECIFICATIONS

Density A Comp. (25°C, g/mL): 1.55 ± 0.10

Viscosity A comp. (25°C, mPa.s): 2000 - 4000

Density A+B comp. (25°C, g/mL): 1,50

Viscosity A+B comp. (25°C, mPa.s): 500 - 2500

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W₃

Adhesion strength by pull-off test (N/mm2): Rigid system without trafficking ≥ 1.0 N/mm², with trafficking ≥ 2,0 N/mm2

Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II

Pot life (23°C): 2 - 3 Hours

Solvent:Organic solvent

Suitable for use as an anti-corrosive primer on all metal surfaces where corrosion resistance is required. It is also used for corrosion protection of concrete structures. It is used as a primer before applications of Isonem Anti Fire Paint Plus for Steel Structures 120 min Fire Resistant Paint

Surface preparation: Application surfaces should be cleaned from foreign objects which reduce adhesion like oil, dust, dirt, etc., and completely dry and clean. Metal surfaces should be sandblasted at least Sa 2 ½ degree and they should be primed with Isonem ANTI RUST PRIMER within 6 hours. After hard drying of the primer is completed (5 - 6 hours later), It is proceed to topcoat application. It should be noted that temperatures of materials are min. +15°C before application.

Application Method: It is produced in ready-to-use sets according to mixing ratios. No thinning is required. Component A is mixed with a low-speed mixer with the appropriate mixing tip and hardener component B is added while continue mixing Care should be taken to ensure that the walls and bottom of the container are mixed well and that the mixture is homogeneous. After the mixture is rested for 10 -15 minutes, it is applied with a short hard bristle brush, short hair roller or airless spray. When the second coat application is required, the application of the second coat should be done when the surface of the first coat dries. If this time has elapsed, the surface should be roughened before the topcoat application.

CONSUMPTION: 0,25 – 0,30 kg/m²

PAINTABLE (COVERAGE) AREA: 15 - 20 m²/5 kg set

COLOR: Off-white

PACKING: 5 kg set (Component A 4,5 kg canister, Component B 0,5 kg canister)

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place away from heat and fire.

MAGNETIC PAINT

ISONEM MAGNETIC PAINT is a dye type that can be sticked on surface materials such as picture back having magnet, poster without any damage to dye thanks to its metal in the structure, is water-based high fusible power, easily dried, resistant to friction, non changing dye and has high performance. Without using any nail, band, screw or sticker, it can be hold on any surface such as wall or wooden like picture, poster. As it is water-based, it has no fragnance and no damage to human health. Although ISONEM MAGNETIC PAINT creates magnet effect, it has no damage to computer monitor, mobile phone, television, credit card and atm card.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 1,57 ± 0,10

pH (25°C): 7.0 – 9.0

Viscosity (25°C, mPa.s) : 12500 - 13500

Solid content (% Weight): 70 ± 2

Water tr.ansmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2) : Crack bridging flexible systems without trafficking ≥ 0.8

Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II

Solvent: Water

Interior walls, schools, hospitals, shopping centers, offices, conference halls, studios

Application surface must be smooth, steady and dust-removal. Before using ISONEM MAGNETIC PAINT, the least two minutes, it must be mixed and it can be applied by using roll and scrub. As increasing magnet feature of surface, it should be applied the least 3 thick layers. The least 30-40 minutes between layer applied should be waited. After these operations, any water based dye on it can be applied.

PAINTABLE (COVERAGE) AREA): 5 - 18 m2/bucket

CONSUMPTION: 1 kg /m2

COLOR: Grey

PACKAGING: 5 kg, 10 kg, 18 kg PP bucket

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

MS 82

It is a very strong synthetic insulation paint which has been modified by special chemicals and polymers to eliminate the moisture and dampness problems in the interior and exterior walls of the buildings because of natural conditions. It can be applied to any kind of humid or dry walls, painted and unpainted surfaces. Thanks to its excellent alkali and moisture resistance, it prevents the formation of moisture on the walls and destroys if there is any. The adhesion strength in all kinds of surfaces is extremely strong, does not swell, high chemical resistance, it is not affected by UV, rain, water or salt. It is used in interior and exterior walls, in basements, in garages or in cellars, in interior walls facing north and in humid areas. It forms a film layer showing excellent moisture resistance on the surface applied. Even if the paint or wall is humid, it adheres very well to the surface. It is not affected by salt water and efflorescence. Thanks to this feature, it is also used to solve the problem of paint swelling in buildings. While ISONEM MS 82 penetrates into the walls and dries up the humidity inside the walls with the special chemicals in its ingredients. ISONEM MS 82 paints do not cause any side effects on the applied surface.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 1,40 ± 0,10

pH (25°C): Not applicable (N/A)

Viscosity (25°C, mPa.s): 2000 - 4000

Solid content (% Weight): 70 ± 2

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W₃

Adhesion strength by pull-off test (N/mm2): Rigid system without trafficking ≥ 1.0 N/mm²

Permeability to water vapour (m): 5 ≤ SD ≤ 50 CLASS II

Solvent: Organic solvent

· On moist walls, on painted or non-painted waIls affected by humidity

· On the interior and exterior walls of the foundation

· On the walls of the basement floor

· On surfaces and floors coated with plaster, concrete, alum, etc

· In tunnels, on the walls of buildings facing north

· In the elimination of problems arising from humidity and moisture.

Surface preparation: ISONEM MS 82 anti moisture paint is ready to use, no primer is required. Formation in black color that occurred on walls must be cleaned before application. The application surface may be humid, damp or dry. It can be applied to painted or unpainted all surfaces. If there are swelling parts on the painted surfaces, the application surfaces should be cleaned and a tough surface should be obtained by using appropriate repair mortar.

Application method: Open the ISONEM MS 82 cover from its original package and mix thoroughly for 3 minutes. After the mixing process, it is recommended to apply with a brush, suitable sprayer or especially synthetic epoxy roller without diluting the product to the existing surface. Apply one coat and wait for 24 hours and apply the second coat. The application areas should be ventilated well and also mask, gloves and protective glasses should be used during application.

COLOR: White

CONSUMPTION: 500 - 600 g / m² (2 layers), 1 kg: 1,5 - 2 m²/can, 5 kg: 8 - 10 m²/can

PACKING: 1 kg and 5 kg can

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place away from heat and fire.

IMPORTANT: The surface should be protected from rain, water, mechanical loads and impacts for 24 hours during and after the application.

The application areas should be ventilated well and also mask, gloves and protective glasses should be used during application.

GRASS PAINT

ISONEM GRASS PAINT is an organic grass coloring agent that paints completely faded and dry grass and plants in a natural green color in order to keep the lawns in high quality and constantly green. It can be produced in the desired green shades as well as in red and yellow colors. ISONEM GRASS PAINT is also used to give the natural green color to sandy areas. It spreads easily on lawn surfaces, it has high adhesion strength and dries quickly in 2-3 hours. The lawns stay green in all climates for four seasons, they are not affected by the irrigation regime and rain. Because it contains no harmful chemicals, heavy metals and other fillers, it does not harm the grass and the environment. ISONEM GRASS PAINT is completely water-based, environmentally-friendly, VOC-free, extremely easy to apply.

FEATURES / ADVANTAGES

Water-based, environmentally friendly

Keeps the lawn areas in good quality and continuous green

Easy to use

Fast drying

· Completely sear, dried grass areas

· Dried plants

· Football fields

· A wide variety of designs and designs should be designed and made in organizations, invitations.

Surface preparation: Before applying ISONEM GRASS PAINT mow the grass area to a height of 2 cm. This ensures that the grass leaves remain upright, and the ISONEM GRASS PAINTcan reach all the pale, dry areas below. Foreign substances and dead plant materials are removed from the grass area by harrowing with a proper rake without damaging the grass leaves.

Application method: 1 kg ISONEM GRASS PAINT can be applied by mixing with 0,500 L water depending on the yellowing rate. In sand painting applications, 250 kg sand can be painted by the spraying method by mixing 1 kg ISONEM GRASS PAINTT with water at a ratio of 1:1. The application should be made close to the ground and with the appropriate pressure to affect all the leaves of the grass on the soil. The low-pressure sprayer is required to obtain the best results. The time required for bonding to the leaf is 3 hours. After this period, the grass area can be opened for use. After 10 days following the application, the grass will grow and routine mowing can be performed. Partial yellow areas that can be seen after the mowing can be retouched. The application of ISONEM GRASS PAINTdoes not have any negative effect on the periodic maintenance and calendar of the grass area. After the application, the spraying system should be cleaned immediately with plenty of water.

CONSUMPTION: 100 - 150 g/m2

PAINTABLE (COVERAGE) AREA: 10 - 15 m²/plastic bottle

PACKING: 1 kg of plastic bottle.

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

ANTI RADIATION PAINT

ISONEM ANTIRADIATION PAINT is a product that acts as a shield against high and low-frequency electromagnetic radiation and at the same time insulates radiation from the area by absorbing the electromagnetic field from media.

TECHNICAL SPECIFICATIONS

Type: Water-based, single comp.

Density (25°C, g/mL): 1.20 ± 0.10

PH (25°C): 7 – 9

Solvent: Water

Viscosity (25°C, mPa.s): 3000 – 6000

Brightness (85 ° angle): ≤ 10, CLASS G3

Thinner: Water

ACCORDING TO MEASUREMENT RESULTS of DOKUZ EYLUL UNIVERSITY ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT;

GSM 900 MHz frequency band up to 30dB (1000 times power attenuation, 99.9%) has been found to have shielding properties. The average shielding values of the relevant samples are given in the table in the commonly used special purpose communication frequency regions. Decibel and percentage of attenuation result:

Decibel and percentage of attenuation results;

GSM base stations, TV and radio transmitters, radar, wireless, wireless networks and power lines in the private areas of the interior and exterior of the housing, hospitals, military facilities and nuclear power plants, such as sensitive places, also used in our daily life of electronic goods (TV, radio, refrigerator, iron, microwave oven, washing machine, dishwasher, telephones, etc.) can be used to prevent the negative effects of emitted electromagnetic radiation and to isolate private living areas from electromagnetic radiation.

Surface preparation: Application surfaces must be cleaned of all kinds of oil, dirt, and rust.

Application method: ISONEM ANTIRADIATION PAINT, ready to be applied, should be applied on one or two layers depending on the shielding effciency of the desired electromagnetic radiation including walls and ceilings on the interior. The application must be applied to all interior surfaces except the floor without spaces. The application is made with a brush. After the first layer has dried, the end of the grounding kit is plugged into an earthed outlet and the silver wire part of the apparatus is stuck with acrylic paste or plaster.The plaster dry after, it is applied one more layer of ISONEM ANTIRADIATION PAINT. After finishing the application, the top coat can be painted with the desired paint or coated with wallpaper or coating products. This situation does not cause weakening of the properties of ISONEM ANTIRADIATION PAINT.

CONSUMPTION: 1 - 1,5 kg/m² (2 Layers)

PAINTABLE (COVERAGE) AREA: 6 – 10 kg/m²

PACKAGING: 5,10 kg in PP bucket

STORAGE: 24 months in original, unopened package, cool and dry environment

Product categories

Social media

Contact

Created a website